The Aliens Legacy http://forum.alienslegacy.com/ |
|
Fanmade: The Motion Tracker (Harry Harris) http://forum.alienslegacy.com/viewtopic.php?f=8&t=2096 |
Page 2 of 2 |
Author: | pezmeister [ Thu Nov 06, 2003 12:00 am ] |
Post subject: | Re: My Motion Tracker... Finished! (Download intensive). |
I remember seeing it just as parts...A* job there Harry..you should be proud...will look great with "Hudson"... Truely beautifull..truely truely brautifull:shock: This user has been classified as Crowe...the silent Marine. Aliens in my loo again!!!! |
Author: | clanger68 [ Thu Nov 06, 2003 3:58 pm ] |
Post subject: | Re: My Motion Tracker... Finished! (Download intensive). |
Quote: Quote:Andy, do you mean the fourth picture down? It's the little 'nozzle' that's on the back of the 'pump' unit. As I mentioned my one is from Deck36 and is made in two parts so as to avoid any seam lines. 'Tis truly a beautiful thing too: Oops, I meant the fourth picture and yes that's the part I was puzzled by, thanks very much for clearing that up. Your right, it certainly is a thing of beauty! Quote: Quote:To answer your question about the washer, you should be able to pick them up from hardware outlets but if you can't find one let me know as I'm sure I have one or two somewhere. I'll have another look around and if I have no luck then I'll certainly be in touch. Quote: Quote:Interestingly Deck36 chose to use a 3mm thick laser-cut plastic disc instead of a washer on their tracker kit. I'm not sure that this was accurate as it's far more likely that Terry Reed and his team would have just grabbed a washer out of their stock of bits & pieces rather than making something specifically. Maybe Deck36 had the same crummy hardware stores in their vicinity as I have!!! Quote: Quote:Hope that helps, Harry. Certainly did, as always! Cheers, Andy "I'm going to live forever, ...........or die trying!!" |
Author: | Safari Joe [ Tue Nov 11, 2003 2:14 am ] |
Post subject: | Re: My Motion Tracker... Finished! (Download intensive). |
WWWOOOWWW!!! BOMBASTIK PIECE OF WORK!!!!! Trully nice job Harry!!!! ( that's I never knows is how a man thats owns an original motion tracker wants another one... ) ADIOS MUCHACHOS and SEMPER PROCINGO. JOIN THE MARINES!!! Visit exotic places,meet nice people... AND NUKE'M ALL... Dany studio_patna@yahoo.com.ar |
Author: | bigbisont [ Fri Jan 26, 2018 6:21 pm ] |
Post subject: | teMP 2 |
*(Continuation of thread and carryover of original material/original author unedited except to add space to accommodate picture upload).* And here it is fully assembled! Attachment: Attachment: Attachment: Using a mix recommended by a few folks (you know who you are, I can't remember - but thanks anyway!) of 50% Humbrol Brown Bess to 50% thinner the colour coat was a great success, but be warned - in that ratio the paint is very thin so care must be taken not to over-spray, which can lead to the paint running. I gave my Tracker about five very thin coats. To stir the Brown Bess thoroughly I used a piece of brass rod about 2" long with a 90° bend at the last ¼" and stirred the paint with that in my Dremel. I cut a disc of plasticard slightly bigger than a Humbrol tin, made a small hole in the middle and put the rod through that. Holding the disc tightly onto the open tin I just ran the Dremel for 30 seconds or so which seemed to do the trick, and no spills! Attachment: Attachment: For the record the 'pump' thing on the bottom, the rear knob and the rod on the left-hand side that connects the rubber tube to the handle are spares that I got from Deck36. I've not installed any electronics as yet as it's principally to be used to display with my Hudson costume when it's on the mannequin. Anyway, enjoy! Harry. |
Author: | bigbisont [ Fri Jan 26, 2018 6:28 pm ] |
Post subject: | |
failed links deleted and pictures from this thread have been directly uploaded. |
Page 2 of 2 | All times are UTC [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |