The Aliens Legacy http://forum.alienslegacy.com/ |
|
Transport of mg42 http://forum.alienslegacy.com/viewtopic.php?f=4&t=18555 |
Page 1 of 1 |
Author: | knoxvilles_joker [ Mon Nov 18, 2019 4:16 am ] |
Post subject: | Transport of mg42 |
Found this online: https://www.brpguns.com/products/MG42-T ... Chest.html Would such a box be a bad idea for the mg56a smart gun? |
Author: | 88reaper88 [ Mon Nov 18, 2019 12:24 pm ] |
Post subject: | |
Not sure the USCM have that big a connection to the Nazis but if it works it works I think someone has made a crate for their smarty but I can’t remember who it was. |
Author: | smrtazzsmrtgnnr [ Mon Nov 18, 2019 12:36 pm ] |
Post subject: | |
My own M56 ended up several inches longer than the stock MG42, so I am pretty sure (mine anyway) would not fit. I ended up using a snow board carry bag for transporting it. |
Author: | Erik_MAA [ Mon Nov 18, 2019 2:11 pm ] |
Post subject: | |
I have a Matsuo M56, which breaks down into two pieces. I bought one of these and use it for transport: https://www.amazon.com/gp/product/B00TY ... UTF8&psc=1 There is enough room in there for the gun and stabilizer arm. I have a separate container I carry the armor in. |
Author: | 577_ops [ Mon Nov 18, 2019 6:26 pm ] |
Post subject: | Re: |
smrtazzsmrtgnnr wrote: My own M56 ended up several inches longer than the stock MG42, so I am pretty sure (mine anyway) would not fit. I ended up using a snow board carry bag for transporting it. Second that! Both size vise and for the used label I would not reccomand using this box. Using a wodden box with the right dimensions as such (apart from the weight) would work. |
Author: | Corp Hicks [ Mon Nov 18, 2019 8:22 pm ] |
Post subject: | |
I would use it for an MG42..., who need an smart gun if u can have the original... |
Author: | Hybrid [ Mon Nov 18, 2019 8:36 pm ] |
Post subject: | Re: |
88reaper88 wrote: I think someone has made a crate for their smarty but I can’t remember who it was. It's Matt [Crashdown] I beleive the crate is custom made with mounts inside to support the smartgun, and UKCM markings on the outside. It even has wheels at one end! |
Author: | Scapey [ Tue Nov 19, 2019 6:50 pm ] |
Post subject: | |
US/UKCM markings on a similar case would be fine, but yeah... I'd have issues if anyone showed up to a con with Nazi insignia anywhere on their gear! We take great pride in being an inclusive group; and homophobia, transphobia, racism and bigotry are emphatically not welcome; display of nazi iconography could very easily give the wrong idea, even if there's no deliberate ill-intent. Shape-wise, that crate design would be fine, assuming your muzzle and stock were removable - My smartgun being built on a de-ac, both unscrew just as with the original gun. I usually just use a bass-case to carry mine though. ( With straps round it, because I don't fully trust even 4 little clasps to keep it shut, given how bloody heavy it is! ) |
Author: | septic [ Tue Nov 19, 2019 10:32 pm ] |
Post subject: | |
I've a Pelican 1770 for mine. It's a beast, but it is long enough, and has wheels too. Bought it cheap without foam, which in hindsight was a mistake as sourcing foam is painful (and expensive). |
Author: | Scapey [ Tue Nov 19, 2019 11:04 pm ] |
Post subject: | Re: |
septic wrote: I've a Pelican 1770 for mine. It's a beast, but it is long enough, and has wheels too. Bought it cheap without foam, which in hindsight was a mistake as sourcing foam is painful (and expensive). I once made a custom foam insert for my pulse rifle; I misted the inside of the peli case ( knockoff ) with water, made a cardboard blank in the shape of my rifle and covered it in cling-film, sprayed some expanding foam into the dead space around it, and topped the lot off with a piece of weighted plywood. Looked a bit rough but did the job well! |
Author: | septic [ Tue Nov 19, 2019 11:52 pm ] |
Post subject: | |
Very interesting idea! Thank you. |
Page 1 of 1 | All times are UTC [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |