| The Aliens Legacy http://forum.alienslegacy.com/ |
|
| Smartgun Construction question http://forum.alienslegacy.com/viewtopic.php?f=3&t=2282 |
Page 1 of 1 |
| Author: | birdie [ Fri Jul 20, 2007 4:38 am ] |
| Post subject: | Smartgun Construction question |
For all you SG experts, I've been trying to work out what the points of attachment are of the front struts, to the MG42 barrel shroud. We can see that the left and right struts are bolted together through a tube on the top, but were they bolted onto the shroud itself at any point? It would seem a little tricky without inpeding the inner barrel. Could they have been welded on? |
|
| Author: | Outcry27 [ Fri Jul 20, 2007 5:24 am ] |
| Post subject: | |
PVB wrote: Have you seen these:
http://visionforgestudios.com/jesse/pro ... roject.htm http://visionforgestudios.com/jesse/pro ... erblue.htm part of this lot: http://visionforgestudios.com/jesse/props/ From a similar thread. He got to the links before I did 
|
|
| Author: | b26354 [ Fri Jul 20, 2007 7:53 am ] |
| Post subject: | Re: Smartgun Construction question |
birdie wrote: For all you SG experts, I've been trying to work out what the points of attachment are of the front struts, to the MG42 barrel shroud.
We can see that the left and right struts are bolted together through a tube on the top, but were they bolted onto the shroud itself at any point? It would seem a little tricky without inpeding the inner barrel. Could they have been welded on? I'm pretty sure there were 2 bolts at the front just below the centerline. At the back of mine I bent a piece of 8mm threaded rod to curve under the barrel and poke out the holes in the side because I didn't want to make too many "permanent" mods to the Shoei. |
|
| Author: | PVB [ Fri Jul 20, 2007 11:50 am ] |
| Post subject: | |
Outcry27 wrote: PVB wrote: Have you seen these: http://visionforgestudios.com/jesse/pro ... roject.htm http://visionforgestudios.com/jesse/pro ... erblue.htm part of this lot: http://visionforgestudios.com/jesse/props/ From a similar thread. He got to the links before I did 
|
|
| Author: | saintadjg [ Fri Jul 20, 2007 4:54 pm ] |
| Post subject: | |
http://s68.photobucket.com/albums/i17/s ... n/?start=0 Some helpful info here http://forum.alienslegacy.com/viewtopic ... t=smartgun |
|
| Author: | birdie [ Fri Jul 20, 2007 5:49 pm ] |
| Post subject: | |
I'm building mine around a Matsuo MG-42. The only found part I don't have is the ammo drum, not sure what I'm gonna do about that yet. Right now I'm just in prep, figuring out the best ways to go about the assembly. Getting the whole barrel assembly connected to the receiver section is looking like the biggest challenge right now, as there is nowhere to sink a bolt on that part of the barrel shroud. |
|
| Author: | saintadjg [ Fri Jul 20, 2007 8:23 pm ] |
| Post subject: | |
try www.mg34.com . |
|
| Author: | Osmotic [ Sat Jul 21, 2007 3:53 pm ] |
| Post subject: | |
Si They are both secured to the weapon at the front below the centre line. As mentioned they are joined via a tube at the top. Only the left strut is fixed at the rear slightly in front of where the front handle riser sits. 
|
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|