The Aliens Legacy
http://forum.alienslegacy.com/

shoulder lamp for smart gun
http://forum.alienslegacy.com/viewtopic.php?f=3&t=19628		 Page 1 of 1
Author:  knoxvilles_joker [ Sun Oct 17, 2021 1:32 am ]
Post subject:  shoulder lamp for smart gun
The shoulder lamp is 3d printed minus the fins which are a resin cast from spat (they look and assemble better). The mounting kit is from spat. The lamp is a 100w cob led array that I have steeped from 7.2vdc to 40vdc on a variable booster. The speaker is a 35w Memphis audio speaker (they have a no questions asked warranty on their pro line stuff and I like how they sound.) The amp is a 12vdc 8w amp made by adafruit. The dc-dc booster is a Chinese unit as I have been unable to source a local stateside unit that has the input/output range and size factor.

I have it set to mount to a 1/8" steel plate that I will have attached to the Steadicam vest with some 2" webbing I got from Knoxville foam and fabric and some buckles from buckleguy.com.

I just got the electronics tested and working this week. The webbing will get installed this coming week and a coat of flat black paint applied. The webbing will get attached with Chicago screws from buckleguy.

Attachment:
IMG_4469.jpg
IMG_4469.jpg [ 1.78 MiB | Viewed 1885 times ]
Author:  septic [ Mon Oct 18, 2021 3:53 am ]
Post subject: 
Have you run the speaker while test mounted? As someone that is slowing losing their hearing, I'd be a little worried about having it close [ish] to my ear ...
Author:  88reaper88 [ Mon Oct 18, 2021 10:10 am ]
Post subject: 
Why does it have a speaker??
Author:  retrogarde [ Mon Oct 18, 2021 2:15 pm ]
Post subject: 
88reaper88 I assume it is to play the audio for the SmartGun firing!
Author:  smrtazzsmrtgnnr [ Mon Oct 18, 2021 9:19 pm ]
Post subject:  Re:
retrogarde wrote:
!


As it was my 3d file, I think it stems from his taking me serious about the hole being for a speaker (being that the original prop WAS an alarm box.) I was recommending a #14 plastic canvas, cut at 45 degrees to X/Y, be used as the grill/cover, allowing the circle hole to be seen (like the prop.)

But, I could be wrong. What do I know... all I do is drive the short bus. :shock: :P
Author:  knoxvilles_joker [ Tue Oct 19, 2021 8:26 pm ]
Post subject:  Re: Re:
smrtazzsmrtgnnr wrote:
retrogarde wrote:
!


As it was my 3d file, I think it stems from his taking me serious about the hole being for a speaker (being that the original prop WAS an alarm box.) I was recommending a #14 plastic canvas, cut at 45 degrees to X/Y, be used as the grill/cover, allowing the circle hole to be seen (like the prop.)

But, I could be wrong. What do I know... all I do is drive the short bus. :shock: :P


I did not quite get that far. For halloween I am doing good just to get the shoulder lamp integrated for light and sfx...
Author:  seven [ Fri Oct 22, 2021 9:23 pm ]
Post subject: 
That is so awesome! who made the mounting clip? that looks clean.
Author:  knoxvilles_joker [ Sat Oct 23, 2021 3:38 am ]
Post subject:  Re:
seven wrote:
That is so awesome! who made the mounting clip? that looks clean.


Mounting clip is one from spatcave. I try to use off the shelf as much as I can so there is not a bigger push to sell things.

This will be shown off at fanboy expo in Knoxville on Halloween weekend.

Robert Patrick, Edward Furlong, and Summer Glau will be there.

I have to ditch the headset hud setup for now until I sort out mounting to counter the weight issue as the electronics has added to the weight.
Author:  knoxvilles_joker [ Wed Nov 10, 2021 11:25 pm ]
Post subject: 
US $0.39 21％ Off | 10W 20W 30W 50W 100W White/Warm white LED CHIP Integrated High Power Lamp Beads 24*44mil 32V-34V 3200K-6500K 600-3000MA
https://a.aliexpress.com/_m0Q6xU6

The lamp used
Page 1 of 1 All times are UTC [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/