The Aliens Legacy http://forum.alienslegacy.com/ |
|
New project M240 http://forum.alienslegacy.com/viewtopic.php?f=3&t=15998 |
Page 1 of 2 |
Author: | shelby [ Tue Mar 22, 2016 9:18 pm ] |
Post subject: | New project M240 |
Hello, i am planning on starting an M240 build in a few weeks and i'm short of a couple of critical dimensions. Can anyone help me with this. I need the diameter's of the body of the fuel reservoir, the centre section and the two bands. Also the neck diameter of the fuel reservoir (were the screw threads would be to mate the reservoir to the flame unit) and/or the width of the flamer were the two join. I've got an M16 iron sight so i've got a good base ref for the uppers but the body flares out below this and i can't seem to get a good picture to work out the angles i need to give me the width of the unit at the point the res and flamer meet. It seems to bulk out quite quickly tho. Any other dimensions for the M240 anyone wants to post would also be appreciated, as this will allow me to check my sizes before i start getting messy especially those pesky widths (most of the photo's i have are side on). Any sage advice or helpful hints from any of the build vets out their, who are in the process of or have completed theirs would also go down a treat. Here's to hoping this build will be easier than my smart gun! ![]() Cheers |
Author: | retrogarde [ Tue Mar 22, 2016 10:23 pm ] |
Post subject: | |
Hey Shelby! Here's my build thread for making an M240: viewtopic.php?f=3&t=14481 Hopefully there will be some information in there to help you out! |
Author: | shelby [ Wed Mar 23, 2016 6:26 am ] |
Post subject: | |
Hi Retrograde, that's brilliant just what I needed. Your build looks amazing, really looking forward to getting back and getting started now ☺ Thanks so much Shelby |
Author: | shelby [ Wed Mar 23, 2016 12:33 pm ] |
Post subject: | |
Does anyone out there know where I can lay my hands on an M204 guard. I've looked in my usual places (ebay and erm ebay ) but had no luck so far. Cheers Shelby |
Author: | gunny63 [ Wed Mar 23, 2016 3:18 pm ] |
Post subject: | Re: New project M240 |
Go to a few militaria shows, the season has already restarted, however, If you can't find one, G&P do a separate one to fit to airsoft M16's |
Author: | shelby [ Wed Mar 23, 2016 4:08 pm ] |
Post subject: | |
Cheers for the headsup Gunny, have just bought myself a G&P handguard ☺ Shelby |
Author: | retrogarde [ Wed Mar 23, 2016 5:26 pm ] |
Post subject: | |
Nice! I bought a surplus one off a member here and felt kind of bad about "wrecking" a vintage item. But that piece is going to help you get the overall dimensions correct, so it really is essential. |
Author: | shelby [ Wed Mar 23, 2016 6:57 pm ] |
Post subject: | |
Was thinking of scratch building one if i had too but as it happens their quite easy to come by when you get pointed in the right direction! Cheers guys this is heading up to be a fun build. Just need to get home now for a couple of weeks of rest and build time ![]() |
Author: | shelby [ Thu Mar 24, 2016 10:34 am ] |
Post subject: | |
Hey retrogarde do you know if the nozzle is still available and could you tell me the thickness of the pistol grip? |
Author: | Hybrid [ Fri Apr 29, 2016 6:06 pm ] |
Post subject: | |
That's great. The M240 is defiantly becoming a must have. |
Author: | shelby [ Fri Apr 29, 2016 6:35 pm ] |
Post subject: | Re: New project M240 |
It's coming together a little slower than my smart gun did (work commitments) but i've managed to source all the bits now i think, just need a little time off to start the build. |
Author: | Hybrid [ Sat Apr 30, 2016 12:00 am ] |
Post subject: | |
My concern is how fragile woukd a build be, could it deal with reasonable rough handling |
Author: | shelby [ Sat Apr 30, 2016 7:52 am ] |
Post subject: | Re: New project M240 |
Oh she'll be solid. Gonna run a mild steel bar through the centre to screw the fitting on one end and hold the barrel square the other. The chassis is going to be marine ply and all the add on's will be screwed and glued. The smart gun was fully welded but not got that option this time. |
Author: | shelby [ Tue May 03, 2016 12:47 pm ] | ||
Post subject: | Re: New project M240 | ||
I'm not going to do get into the full build thing as retrogarde has already done an amazing one of those. So i'll just put up some pics now and then when i hit the milestones!! Well as you can see the M16 sections are now cut just need to get back to the UK so i can make a start on the chassis. The more i look at the photo's the more i think i have the right connection for the back end, if not they look really close to me. Does anybody know what the movie one's were?
|
Author: | shelby [ Tue May 24, 2016 7:07 pm ] | ||
Post subject: | Re: New project M240 | ||
Ok folks, the back end is coming on nicely! The thread bar is there to strengthen the back end. The handle is the next on the hitist and is drying in the workmate at the moment ![]()
|
Author: | SulacoBoy [ Tue May 24, 2016 7:37 pm ] |
Post subject: | |
Sweet! |
Author: | retrogarde [ Tue May 24, 2016 10:19 pm ] |
Post subject: | |
Love it! |
Author: | veektohr [ Wed May 25, 2016 12:51 am ] |
Post subject: | |
I love seeing these 240 builds recently. Any intention of having the pilot (for lack of a better term) flare functional? Would be pretayyyyyyyyy sweet ![]() |
Author: | shelby [ Wed May 25, 2016 3:26 pm ] |
Post subject: | Re: New project M240 |
Probably not a good idea as my nozzles made of PVC, so afraid not anything that fancy ![]() |
Author: | shelby [ Thu Jun 02, 2016 10:50 pm ] | ||||
Post subject: | Re: New project M240 | ||||
Just had a few unexpected day's off work, so i had a little time to play. The screws on the sections above the pistol grips are not yet countersunk but they will sit flush compared with their current positions, i just got carried away with other more interesting bits! so i'll have to address it when i get back. Apologies for the orientation of the first picture and their kinda in the wrong order but i'm much more of a hands on tools kinda person, the girlfriend usually handles the computer stuff!! ![]()
|
Author: | veektohr [ Fri Jun 03, 2016 5:11 am ] |
Post subject: | |
Awesome progress, you're really moving fast! |
Author: | shelby [ Fri Jun 03, 2016 7:46 pm ] | ||
Post subject: | Re: New project M240 | ||
Last day of fun before work steps in again, the carry handle is now in and secured and the nozzles have been started just letting those dry. The thread bar coming from the bottom is just a scrap piece of bar to hold the securing nut in place whilst the epoxy drys around it, the fuel tank will have a central threadbar running its entire height not just to secure it into the securing nut but also clamp the whole assembly together, making it super strong oh and give it some more weight! There's a couple of things i've decided to change ( hindsights a wonderfull thing) when i get back, i have to countersink those pesky securing screws, and there's a serious amount of sanding throughout. The fuel tank bodies have just arrived but all of these jobs will have to wait a couple of weeks. Plus side it'll give the epoxy time to harden, down side i'll have more time to think about the changes i'm going to make and start getting creative, never a good idea!! ![]() P.S I know its upside down please see previous post!
|
Author: | NeedanID [ Fri Jun 03, 2016 7:55 pm ] |
Post subject: | |
nice work... you are flying along on your build compared to my glacial progress. |
Author: | shelby [ Fri Jun 03, 2016 8:59 pm ] |
Post subject: | Re: New project M240 |
Unfortunatly on an enforced all-stop now for a few weeks, for glacial you wanna see my sentry gun, taken about two years so far! ![]() |
Page 1 of 2 | All times are UTC [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |